What does Sitting Pressure and the Standing-Desk Myth conclude, in numbers, about “A Five-Centimetre Lever Arm: How Forward Bending Multiplies Lumbar Compression”?
Answer: Chapter 3 writes down a lever with an arm of about 5 centimetres, on which a forward bend of about twenty degrees doubles the pressure.
Scope of the numbers: Its parameters are illustrative; all calculations are generated by its programs. The book is not medical advice and claims no health effect for any intervention; readers with existing back problems should consult a licensed physician before changing a workstation or starting a self-experiment.
Data table
The numbers below are printed verbatim by the chapter's Python program and can be reproduced by running it. standard-library Python only
| flex deg | muscle N | compress N | P MPa | x upright |
|---|---|---|---|---|
| 0 | 82 | 600 | 0.50 | 1.00 |
| 5 | 262 | 778 | 0.65 | 1.30 |
| 10 | 440 | 952 | 0.79 | 1.59 |
| 15 | 616 | 1120 | 0.93 | 1.86 |
| 20 | 787 | 1280 | 1.07 | 2.13 |
| 30 | 1112 | 1575 | 1.31 | 2.62 |
| 45 | 1539 | 1936 | 1.61 | 3.23 |
| 60 | 1867 | 2179 | 1.82 | 3.63 |
| Wilke 'standing, bent forward' 1.10 MPa = 21.3 deg | ||||
| muscle share of compression at 20 deg: 0.615 | ||||
| each 1 cm of extra lever adds 82 N |
Show the full program
# Chapter 3. p31: trunk moment / 5 cm erector arm -> compression vs flexion
# 静力学(参数示意;力臂 5 cm 为教科书常用近似,Chaffin 等):
# F = W cos(t) + W (E0 + L sin(t)) / R + C
# W = 0.60 * 70 kg * g;E0 = 0.01 m 直立时质心前移;L = 0.25 m 为
# L4-L5 到上身质心的距离;C = 106 N 张力性肌力(标定到站立 0.50 MPa)
# P = 1.5 F / 1800 mm2,与 p11 同一换算
# Winter 教科书:头、上肢与躯干(HAT)约占体重 0.678;腰椎以上取 0.60
import math
G = 9.81
W = 0.60 * 70.0 * G
R, E0, L, C = 0.05, 0.01, 0.25, 106.0
K_NACH, AREA = 1.5, 1800.0
def comp(t_deg, r=R):
t = math.radians(t_deg)
return W * math.cos(t) + W * (E0 + L * math.sin(t)) / r + C
def mpa(f):
return K_NACH * f / AREA
base = comp(0.0)
print("flex deg muscle N compress N P MPa x upright")
for t in (0, 5, 10, 15, 20, 30, 45, 60):
f = comp(t)
m = W * (E0 + L * math.sin(math.radians(t))) / R
print("{:8d} {:9.0f} {:11.0f} {:7.2f} {:10.2f}".format(
t, m, f, mpa(f), f / base))
lo, hi = 0.0, 60.0
for _ in range(60):
mid = (lo + hi) / 2.0
if mpa(comp(mid)) < 1.10:
lo = mid
else:
hi = mid
print("Wilke 'standing, bent forward' 1.10 MPa = {:.1f} deg".format(lo))
print("muscle share of compression at 20 deg: {:.3f}".format(
(comp(20.0) - W * math.cos(math.radians(20.0)) - C) / comp(20.0)))
print("each 1 cm of extra lever adds {:.0f} N".format(W * 0.01 / R))Single source and citation
Fan, Y. (2026). Sitting Disc-Pressure Levers, the 135-Degree Recline and the Standing-Desk Energy Myth (Version 1.0.0), Chapter 3: A Five-Centimetre Lever Arm: How Forward Bending Multiplies Lumbar Compression. 5D Library. DOI pending
DOI pending · monograph page goes live after publication · 5DL-B-184 · v1.0.0 · CC-BY-NC-ND-4.0
BibTeX
@book{fan2026184,
author = {Fan, Yafu},
title = {Sitting Disc-Pressure Levers, the 135-Degree Recline and the Standing-Desk Energy Myth},
year = {2026},
publisher = {5D Library},
edition = {1.0.0},
note = {DOI pending}
}Other chapter answers in this book
- Chapter 1 · Pressure in Vivo: Why the Upright Sitting Posture Is Not the Lowest Load
- Chapter 2 · One Hundred and Thirty-Five Degrees: the Backrest Takes the Load, the Hip Frees the Pelvis
- Chapter 4 · Nine Kilocalories an Hour: the Standing-Desk Energy Myth and the Real Ledger
- Chapter 5 · Poisson Switching: Why the Cumulative Load Integral Cannot See the Cost of Staying Still
- Chapter 6 · Workstation Geometry: Seat Height, Footrest, Standing Desk and the Screen After Reclining
- Chapter 7 · The Crooked Mat and the Bound Sapling: Classical Sources East and West Examined
- Chapter 8 · Closing the Loop: the Workstation Parameter Card, the Thirty-Minute Reminder and the Two-Week Diary