What does Cold Immersion and the Hypertrophy Penalty conclude, in numbers, about “Cooling Dose, Residual Muscle Cooling and the Core Safety Margin”?

Answer: In the equivalent-cylinder model, a 3-minute plunge at 3 °C cools the top of the muscle only to 34.6 °C, ten minutes at 10 °C take it to 31.7 °C, and protocols of 20 minutes or an hour bring it to about 29 °C; after exit the deeper muscle keeps cooling. A plunge of a few minutes barely touches core temperature, whereas an hour of immersion can take a lean core to 33.44 °C or below, followed by an afterdrop after leaving the water. The cooling dose should be measured in degree-minutes of muscle temperature, not in water temperature. The next chapter leaves the laboratory to read what two classical texts said about cold.

Scope of the numbers: Its parameters are illustrative; all calculations are generated by its programs; it is not medical advice, claims no health benefit, and asks readers to consult a licensed physician before any self-experiment. Chapter 5 derives a rule for the gap between training and cold water: with illustrative parameters a 6-hour gap cuts the interference to 0.135 of an immediate plunge, for a predicted growth ratio of 0.910.

中文版

Data table

The numbers below are printed verbatim by the chapter's Python program and can be reproduced by running it. standard-library Python onlyprinted values that match the answer: 10, 20, 31.7, 34.6

muscle C at exit and 30 min later; top = just under the fat
protocol water min | exit top1cm | +30 top 1cm | kJ kcal
plunge 3C3 3 | 34.6 36.1 | 33.0 34.4 | 608 38.4
Roberts10 10 | 31.7 35.5 | 32.6 34.1 | 877 72.0
Fyfe10 15 | 30.4 34.8 | 32.2 33.8 | 1101 96.0
Fuchs8 20 | 29.0 33.9 | 31.6 33.2 | 1416 120.0
Sramek14 60 | 28.9 32.8 | 31.3 32.7 | 2363 272.7
Show the full program
# Chapter 6. p61: Muscle temperature under five published protocols.
# The p31 cylinder (10 mm fat, h = 250 W/m2K, illustrative tissue
# values, Pennes perfusion, metabolism from the Sramek 2000 law with a
# 3-minute lag that carries over after exit) is run for protocols
# named after studies: 3 min at 3 C (a typical commercial plunge),
# 10 min at 10 C (Roberts 2015), 15 min at 10 C (Fyfe 2019), 20 min at
# 8 C (Fuchs 2020 used legs only; here the whole cylinder) and 60 min
# at 14 C (Sramek 2000). After exit the body sits in 22 C air (h = 10).
# We print muscle temperatures at exit and 30 min later, heat lost in
# the water, and the p21 metabolic excess for the same protocol.
# 中文注:五种文献方案下的肌肉温度与散热量(含出水后的余冷)。
import math

A_SURF, R_OUT = 1.8, 0.072
LEN = A_SURF / (2.0 * math.pi * R_OUT)
DR, DT = 0.001, 0.5
RHOC_B = 1060.0 * 3800.0
TISSUE = {  # k W/mK, rho*c J/m3K, perfusion 1/s
    "skin": (0.37, 1100.0 * 3400.0, 2.0e-4),
    "fat": (0.20, 920.0 * 2350.0, 1.0e-4),
    "muscle": (0.42, 1050.0 * 3600.0, 5.0e-4),
}
C_CORE = 40.0 * 3500.0
REST = 83.7


def extra_frac(tw):
    t_th, k = 22.17, 42.8 / 100.0
    return min(4.0, max(0.0, k * (t_th - tw)))


def build(fat_mm):
    layers = ["muscle"] * 20 + ["fat"] * fat_mm + ["skin"] * 2
    r_core = R_OUT - DR * len(layers)
    rs = [r_core + (i + 0.5) * DR for i in range(len(layers))]
    return layers, r_core, rs


def run(fat_mm, t_env, h, minutes, state=None, core_fixed=False,
        sample=()):
    layers, r_core, rs = build(fat_mm)
    n = len(layers)
    temps = list(state[0]) if state else [36.0] * n
    tc = state[1] if state else 37.0
    met = state[2] if state else 0.0
    k = [TISSUE[x][0] for x in layers]
    cap = [TISSUE[x][1] * 2.0 * math.pi * rs[i] * DR * LEN
           for i, x in enumerate(layers)]
    perf = [TISSUE[x][2] * RHOC_B * 2.0 * math.pi * rs[i] * DR * LEN
            for i, x in enumerate(layers)]
    g = []
    for i in range(n - 1):
        rf = r_core + (i + 1) * DR
        kf = 2.0 * k[i] * k[i + 1] / (k[i] + k[i + 1])
        g.append(kf * 2.0 * math.pi * rf * LEN / DR)
    g_in = k[0] * 2.0 * math.pi * r_core * LEN / (DR / 2.0)
    r_o = (DR / 2.0) / (k[-1] * 2.0 * math.pi * R_OUT * LEN) \
        + 1.0 / (h * 2.0 * math.pi * R_OUT * LEN)
    g_out = 1.0 / r_o
    steps = int(round(minutes * 60.0 / DT))
    drive, lost = extra_frac(t_env) * REST, []
    out = {}
    for s in range(steps + 1):
        tsec = s * DT
        q_out = g_out * (temps[-1] - t_env)
        skin_t = temps[-1] - q_out / (k[-1] * 2.0 * math.pi * R_OUT
                                      * LEN / (DR / 2.0))
        for mark in sample:
            if abs(tsec - mark * 60.0) < DT / 2.0:
                out[mark] = (skin_t, temps[19], temps[10], q_out, tc)
        if s == steps:
            break
        flux = [0.0] * n
        q_core = g_in * (tc - temps[0])
        flux[0] += q_core
        for i in range(n - 1):
            q = g[i] * (temps[i] - temps[i + 1])
            flux[i] -= q
            flux[i + 1] += q
        flux[-1] -= q_out
        p_tot = []
        for i in range(n):
            qp = perf[i] * (tc - temps[i])
            flux[i] += qp
            p_tot.append(qp)
        met += DT * (drive - met) / 180.0
        if not core_fixed:
            tc += DT * (REST + met - q_core - math.fsum(p_tot)) / C_CORE
        temps = [temps[i] + DT * flux[i] / cap[i] for i in range(n)]
        lost.append(q_out * DT)
    return (temps, tc, met), out, math.fsum(lost)



def extra_kcal(tw, minutes):
    return 1.2 * extra_frac(tw) * (minutes + 5.0)


PROTOCOLS = (("plunge 3C", 3.0, 3), ("Roberts", 10.0, 10),
             ("Fyfe", 10.0, 15), ("Fuchs", 8.0, 20),
             ("Sramek", 14.0, 60))
print("muscle C at exit and 30 min later; top = just under the fat")
print("protocol  water min | exit top  1cm | +30 top  1cm |   kJ  kcal")
warm, _, _ = run(10, 25.0, 10.0, 120.0, core_fixed=True)
for name, tw, mins in PROTOCOLS:
    st, m1, q = run(10, tw, 250.0, mins, state=warm, sample=(mins,))
    _, m2, _ = run(10, 22.0, 10.0, 30.0, state=st, sample=(30,))
    a, b = m1[mins], m2[30]
    print("{:9s} {:4.0f} {:4d} | {:8.1f} {:5.1f} | {:7.1f} {:5.1f} |"
          " {:4.0f} {:5.1f}".format(name, tw, mins, a[1], a[2], b[1],
                                    b[2], q / 1000.0,
                                    extra_kcal(tw, mins)))

Single source and citation

Fan, Y. (2026). Cold-Immersion Heat-Flow Equations, Brown-Fat Non-Shivering Thermogenesis and the Post-Training Cryotherapy Hypertrophy Penalty (Version 1.0.0), Chapter 6: Cooling Dose, Residual Muscle Cooling and the Core Safety Margin. 5D Library. DOI pending

DOI pending · monograph page goes live after publication · 5DL-B-183 · v1.0.0 · CC-BY-NC-ND-4.0

BibTeX
@book{fan2026183,
  author    = {Fan, Yafu},
  title     = {Cold-Immersion Heat-Flow Equations, Brown-Fat Non-Shivering Thermogenesis and the Post-Training Cryotherapy Hypertrophy Penalty},
  year      = {2026},
  publisher = {5D Library},
  edition   = {1.0.0},
  note      = {DOI pending}
}

Other chapter answers in this book